Topic: Evinrude 4423 Sportwin – Antique Outboard Motor Club,Inc

This topic has 12 replies, 5 voices, and was last updated 4 years, 11 months ago by David Bartlett.

Viewing 10 posts - 1 through 10 (of 13 total)

1 2 →

Author

Posts
May 19, 2019 at 8:50 pm #175548
David Bartlett
Participant
US Member - 2 Years
I picked up a nice little Sportwin yesterday. Model 4423. Serial #87769.

Has the wrench and shear pins under the cover.

Has spark and a clean gas tank. I need to have a look at the carburetor next. This one looks interesting.

David Bartlett
Pine Tree Boating Club Chapter

"I don't fully understand everything I know!"
- This topic was modified 4 years, 11 months ago by Mumbles.
May 19, 2019 at 11:47 pm #175555
davidk
Participant
US Member - 2 Years
Good pick, DB! Show us the wrench. I don’t know about that accessory.
May 20, 2019 at 7:53 am #175557
David Bartlett
Participant
US Member - 2 Years
Here ya go. Have the screwdriver tiller handle too.

David Bartlett
Pine Tree Boating Club Chapter

"I don't fully understand everything I know!"
- This reply was modified 4 years, 11 months ago by Mumbles.
May 21, 2019 at 12:16 am #175625
Mumbles
Participant
Have you tried starting it yet as it seems the 3/8″ primer cups on these motors go bad and then they drip fuel mix or won’t prime the motor for starting. That’s nice having the original wrench and a full load of shear pins under the cover to!
May 21, 2019 at 6:34 am #175630
davidk
Participant
US Member - 2 Years
Did you get the decoder ring? Without that, it’s just a parts motor.
- This reply was modified 4 years, 11 months ago by davidk.
- This reply was modified 4 years, 11 months ago by davidk.
May 21, 2019 at 7:20 am #175633
David Bartlett
Participant
US Member - 2 Years
Jim,

I have not tried putting gas in it yet. Soon, though!

David Bartlett
Pine Tree Boating Club Chapter

"I don't fully understand everything I know!"
May 21, 2019 at 7:35 am #175634
labrador-guy
Participant
US Member - 2 Years
That wrench is pretty cool! I have a couple motors with the shear pin holder but no wrench. Did the wrench come with these motors does anybody know? I will have to keep an eye out for one.

dale
May 21, 2019 at 8:19 am #175636
David Bartlett
Participant
US Member - 2 Years
Dale,

The wrench was included with the motor, along with the screwdriver tiller grip. The parts breakdown on these motors shows the part #’s.

This is the first of these motors I have so it is new to me.

David Bartlett
Pine Tree Boating Club Chapter

"I don't fully understand everything I know!"
May 22, 2019 at 9:01 pm #175816
David Bartlett
Participant
US Member - 2 Years
The Sportwin is a runner. I got the carb cleaned and back together tonight, used a Quad ring for a sediment bowl gasket and it started. I will post a video tomorrow as it is dark here at the moment! With any luck it will pump water!

David Bartlett
Pine Tree Boating Club Chapter

"I don't fully understand everything I know!"
May 22, 2019 at 9:25 pm #175818
DonWaldo
Participant
Is the screen necessary in the 1940 evinrude sportwin carb mounting gasket? Gasket is looking rough anymore and I need to make a new one.Any info would be much appreciated. 🙂
- This reply was modified 4 years, 11 months ago by DonWaldo.
Author

Posts